Receive for your contractor’s license. Once you’ve passed your licensing exam, registered your business through the proper channels and shown proof of liability insurance, you can submit an official application to receive your contractor’s license. This can be done online or by mail. Following a short review process, you’ll be issued your license, after which you can get to work securing jobs and building your business’s reputation.[20]
Sorry it is difficult to trust almost anyone in the trades. It is easier to do the work myself and not deal with strangers in and around my house. When I have to hire someone I tell them up front that I'll be checking every detail, pay extra to purchase the materials myself, and if they don't want the job - well good! I always fine someone who will work with me as I pay a bonus for that.
When their bids are successful, contractors meet customers to finalize their requirements and plan the order and timing of work. Contractors estimate the time required for surface preparation, painting several coats and drying time between coats. For interior painting jobs, they might have to allow time for clearing rooms. Exterior painting schedules might be dependent on the weather in different parts of the country. Exterior painting is not practical in very wet or very cold conditions.
Keep an eye on the new cans as they're being brought in. Make sure they look new and don't have paint in the rim of the can. If it's a five-gallon bucket, check to see whether the lid is still sealed on with the plastic strip. The only time it's acceptable to mix water in the paint is when you're using a deep or ultra deep base paint to reduce its stickiness, which is rare with new paint technology. Dark primary colors are composed almost entirely of tint that makes it very hard to work with without adding water.

If there is any peeling — and there usually is somewhere — it's essential to scrape off any loose paint. This doesn't just mean the parts that are already separated from the wood and ready to fall off on their own. Each spot where paint has peeled loose needs to be scraped thoroughly until you can no longer get the sharp corner of a putty knife under any of the surrounding edges of paint. Then, the bare spot needs to be sanded until the paint edges are smooth.
To solidify this response, we have been in business for over 30 years as a painting contractor. We didn't just paint a couple of houses 25 or 30 years ago, we paint approximately 900-1000 painting jobs per year and operate with 40 professional painters doing commercial, residential and industrial painting. This article on behalf of Angie's List is totally asinine! I was under the impression Angie's List was only carrying "legitimate" contractors with established reputations. This article written is primarily referring to bottom feeding, one man band operations, trying to hustle for a paycheck.

If your home was built before 1978, there is a good chance that lead paint was used in its construction. Scraping, sanding, or removing old paint can release toxic lead dust which can cause serious illness in children and pregnant women. Special handling is required when working with lead-based paints. If lead paint is present in your home, you will need to hire a lead-certified painting contractor or lead abatement contractor. Before getting started with your exterior painting project, consult your local building authority or visit www.epa.gov for more information.


Thorough preparation is essential to ensure a good finish. Contractors might have to fill cracks or holes and remove old paint if it is badly worn, peeling or flaking. They remove all paint and apply a suitable primer to the bare surface. If the existing paint is in reasonable condition, they clean it and rub it with abrasive material to provide a key for the new paint. On new surfaces, such as bare wood or fresh plaster, they apply a suitable seal, followed by a primer coat.
To maintain a wet edge, start near a corner and run the roller up and down the full height of the wall, moving over slightly with each stroke. Move backward where necessary to even out thick spots or runs. Don’t let the roller become nearly dry; reload it often so that it’s always at least half loaded. Keep the open side of the roller frame facing the area that’s already painted. That puts less pressure on the open side of the roller, so you’re less likely to leave paint ridges when doing DIY wall painting. 

The Evolution System uses a 100% solids polyurea with unique technology that offers extreme adhesion, rapid cure, and maximum broadcast times. The vinyl flakes come in a variety of blends to mix and match with your choice of basecoat colors. This is one of the most popular systems for because of its wide variety of applications. Walk on in 4 hours & drive on in 24 hours.
Some proposals simply say to paint the walls and ceiling and never specify the number of coats to be applied. If the colors are similar enough, it's possible to get away with one coat of paint and not discount your pricing. No matter how hard you try, tiny, pin-sized air holes will pop exposing the original walls. This may not bother you if you can't notice it, but principally speaking you should have paid your painter less for the work.
I'm hiring an interior painter and that is why I was reading this comment list. I'm concerned about your comment about Angie's List. Some of us don't have personal recommendations for tradespersons, and rely on sites like this. Are you saying that Angie's List's reviews are not complete or that they do not print some of the negative reviews? It's hard to know what to do - I have not been able to find a person who just had their paint done so I can ask him/her about the quality of the painter.
If you're going to do any part of the painting or prep work on your own, you must know that the first step in preparing a surface is washing it. Since dirt can affect the smoothness of a surface area -- and therefore paint's adhesion to it -- use soap to remove any dirt or stains. Make sure there's no soap left on the walls when you're finished; also make sure to remove any gloss with sandpaper and vacuum up the leftover dust.
When hiring a contractor it is always best to hire one who is personally referred to you by someone you trust. Hiring through ads or phone book is hit and miss. Check with your local paints stores, they know the good guys from the bottom feeders. Go to the stores that sell the high quality paints like Benjamin Moore(nonpareil), Pittsburg, Sherwin Williams or Glidden. Don't go the the big box stores for referrals, the people there don't know squat!
×